We hope one of the documents on the related list might be meet to your demand and prerequisite. Millions discover their favorite reads on issuu every month. Give your content the digital home it deserves. Get it to any device in seconds. Ricoh aficio service manual. Publish for free today.
Duplex Unit B only BIT SW Immediate Transmission Before disassembling or assembling parts of the copier and peripherals, make sure that the power cord is unplugged. The wall outlet should be near the copier and easily accessible. Note that some components of the copier and the paper tray unit are supplied with electrical voltage even if the main power switch is turned off. If a job has started before the copier completes the warm-up or initializing period, keep hands away from the mechanical and electrical components because the starts making copies as soon as the warm-up period is completed.
The inside and the metal parts of the fusing unit become extremely hot while the copier is operating. Be careful to avoid touching those components with your bare hands. Toner and developer are non-toxic, but if you get either of them in your eyes by accident, it may cause temporary eye discomfort. Try to remove with eye drops or flush with water as first aid. If unsuccessful, get medical attention. The copier and its peripherals must be installed and maintained by a customer service representative who has completed the training course on those models.
Do not incinerate toner bottles or used toner. Toner dust may ignite suddenly when exposed to an open flame. Dispose of used toner, developer, and organic photoconductors in accordance with local regulations.
These are non-toxic supplies. Dispose of replaced parts in accordance with local regulations. The optical housing unit can only be repaired in a factory or at a location with the requisite equipment. The laser subsystem is replaceable in the field by a qualified Customer Engineer. The laser chassis is not repairable in the field. Customer engineers are therefore directed to return all chassis and laser subsystems to the factory or service depot when replacement of the optical subsystem is required.
Use of controls, or adjustment, or performance of procedures other than those specified in this manual may result in hazardous radiation exposure. Laser beams can seriously damage your eyes. This manual uses several symbols and abbreviations. The meaning of those symbols and abbreviations are as follows:. If there is a fax unit in the machine, print out all messages stored in the memory, the lists of user programmed items, and the system parameter list.
If there is a printer option in the machine, print out all data in the printer buffer. Turn off the main switch and disconnect the power cord, the telephone line, and the network cable. Less than 0. Avoid areas exposed to sudden temperature changes:.
Do not place the machine where it will be exposed to corrosive gases. Do not install the machine at any location over 2, m 6, ft. Place the copier on a strong and level base. Inclination on any side should be no more than 5 mm. Do not place the machine where it may be subjected to strong vibrations. NOTE: 1 The recommended mm front space is sufficient to allow the paper tray to be pulled out.
Additional front space is required to allow operators to stand at the front of the machine. Additional right space is required to allow operators to fix paper jams and use the by-pass tray. Make sure that the wall outlet is near the copier and easily accessible. After completing installation, make sure the plug fits firmly into the outlet. Be sure to ground the machine. Separate the PCU into two sections as shown 5 screws. Distribute one pack of developer [A] evenly across the width of the development unit, into all openings.
NOTE: 1 To prevent foreign material. Reassemble and reinstall the PCU. Reposition the holder and press down the holder lever to secure the bottle. Pull out the paper tray and turn the. Adjust the end and side guides to match the paper size. NOTE: To move the side guides, first release the green lock on the rear side guide. If they are not, adjust. Initialize the electric total counter using SP in accordance with the type of.
Check the quantity and condition of the accessories against the following list. Remove the left scale [A] 2 screws.
Place the DF exposure glass. Peel off the backing [D] of the double-sided tape attached to the rear side of the scale guide [E], then install it 2 screws removed in step 2. Install the two stud screws [F]. Mount the DF on the copier, then slide the DF to the front. Secure the DF unit with two screws [G]. Connect the cable [H] to the copier. Attach the appropriate scale decal [I] as shown. Turn the main power switch on. Then check if the document feeder works properly.
Make a full size copy, and check that the side-to-side and leading edge registrations are correct. If they are not, adjust the side-to-side and leading edge registrations. Remove the strips of tape. Attach the adjuster [A] to the base plate, as shown. NOTE: If a table is installed, this step is unnecessary. Set the copier on the paper tray unit. NOTE: When installing the copier, be. One-tray copier model B :.
Install the two brackets [A] 1 stepped screw each. Connect the connecting harness. NOTE: There are cutouts in the plug on both sides. The left side has one cutout, and the right side has two. Reinstall the cover removed in step 3 1 rivet. Install the four brackets [C] 2 screws each. If they are not, adjust the registrations 3. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox.
Please check your email for further instructions. Enter a new password. Ambient Less than 1, lux do not expose to direct sunlight. Illumination: 4. Ambient Dust: Less than 0. Avoid areas exposed to sudden temperature changes: 1 Areas directly exposed to cool air from an air conditioner.
Avoid multi-wiring. DC24 V 1. Open the front door and remove the toner bottle holder [A]. NOTE: 1 To prevent foreign material from getting on the sleeve rollers, place a sheet of paper under the development unit.
Shake the toner bottle [C] several [D] times. Unscrew the bottle cap [D] and insert the bottle into the holder. Pull out the paper tray and turn the paper size dial to the appropriate size. Installation Plug in the main power cord and turn on the main switch.
Select the correct display language using UP Mode Language. Load the paper in the paper tray and make a full size copy, and check if the side-to-side and leading edge registrations are correct.
Initialize the electric total counter using SP in accordance with the type of service contract. Install the platen cover [A] 2 screws. Place the DF exposure glass [B] on the glass holder.
Remove the cover [A] 1 rivet.
0コメント